What is a post pounder called?
A post pounder, post driver, post rammer, post knocker or fence driver is a tool used for driving fence posts and similar items into land surfaces. It consists of a heavy steel pipe which is closed at one end and has handles welded onto the sides. It is normally used by one person, but larger versions may require two.
How much does at post pounder cost?
On average, you’ll spend between $5,000 and $11,000 for a post driver for your skid steer. If you choose a used model, you typically save around 40 to 50 percent. Don’t buy a used model until you see it in operation, either live and in person or via live video.
What size t post do I need for a 4 ft fence?
When figuring out what size T-post to use for a four-foot fence, remember that you will drive the posts about two feet into the ground. This means you need posts that are at least 24 inches longer than how tall you want your fence. For a four-foot fence, you should use T-posts that are at least six feet long.
How far apart should fence posts be for chicken wire?
Drive the Fence posts into the ground with a sledge hammer or post driver, if you have one. Be sure to place your fence posts at least 6-8 inches into the ground so that the soil plate is completely buried. Each post should be placed no more than 10 feet apart.
Can you hammer in T posts?
Post less than 4 feet in overall length may be installed with a common hammer or sledgehammer. … Emergency repairs can also be completed using a hammer or sledge hammer.
How do I drive a post to hard ground?
“You can use either a pneumatic hammer drill that runs off an air compressor, or an electric hammer drill and a generator. These work fairly well, if you use a heavy-duty industrial model. A small one won’t do the job in big rocks,” he says. With a good drill, you can put posts into fairly solid rock.
What is the best t post driver?
- Titan PGD2875 Gas Powered Post Driver.
- Skidril 2-stroke Gas Powered Post Driver.
- Rhino GPD40 Fence Pro Honda 4-stroke Gas Powered Post Driver.
- Titan PGD3875 4″ Barrel Post Driver.
- BSTOOL 2-stroke Gasoline Petrol Post Driver.
- Rhino Ranch Pro.
- Yescom 32.7cc 2-stroke.
- Rhino Multi Pro.
Do petrol post drivers work?
Very reliable and easy to use. The petrol post driver is good and save some hard work but is not quicker than do by hand and damages the post more than a hand driver. Would be ok on metal post other than timber.
Does fence go on inside or outside of posts?
The ‘quick’ answer is that the finished, or good side of the fence faces the outside of your property, visible to neighbors and the outside world. That being said, the fence posts (or poles), rails, and other hardware are installed on the inside of the fence line and face you.
What is a Mansaver?
This lightweight, portable fence post driver is ideal for ranches, vineyards, sign and highway fence posts, and marker installations. …
How far apart do you put T posts?
You should position T-posts no more than 8 feet apart.
How far apart should T posts be for welded wire fence?
The typical spacing of posts is between 8′ and 12′. The distance should be determined by the type of fence and the amount of support that the fence needs in order to stay taught.
Who invented the post pounder?
Inventor of Man Saver Post Driver
Since 1998, Dan Rohrer’s innovative product has sold nearly 16,000 units. Starting a business from scratch is never easy, something that Dan knows well.
How do you start a post pounder?
How is the Post Pounder used. It’s easy, start the engine, then just lift the Post Pounder on top of the post and squeeze the throttle. The hammer, powered by a HONDA engine, strikes 1720 times a minute, pounding posts, like a much larger and heavier machine.
How long is a post driver?
The driver is 78 inches long overall and weighs 30 pounds. The 38- inch-long barrel, which is 2 inches in diameter, allows a 36-inch stroke. The 13⁄8-inch-diameter handles extend down from the lower section of the barrel.
How deep should a wooden fence post be in the ground?
Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
Should fence posts be set in concrete?
Setting Fence Posts in Concrete
Concrete is the most secure material for setting fence posts, especially if you have sandy soil. … Using premixed concrete rather than dry concrete will ensure ultimate security. While concrete is sturdy, it lacks the drainage of gravel and can trap moisture, ultimately leading to rot.
How do you use a post puller plate?
Place a chain hook through the chain hole or loop. Place the T-Post Puller around the t post, and pull the t post out. No more chain slipping off or wrapping the chain around the t posts every time. Simply slide around the t post post and pull up.
How far apart should fence posts be?
Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn’t cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.
How many fence posts do I need for 1 acre?
If we assume that your property is equal on 4 sides, then it is as simple as taking the square root of 43,560 square feet. This gives you 209 feet on each side, which would require 835 linear feet of fence to enclose the entire acre property (209 feet times four sides is equal to 835 linear feet).
How many bags of cement do I need for a fence post?
1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.
How far apart do you put 4×4 fence post?
Too far apart and the strength of your fence is compromised; too close and your fence may look strange. For most privacy and general-purpose fences, 6 or 8 feet between posts is standard.
Is 2 feet deep enough for fence posts?
2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.
What size fence post do I need for a 5ft fence?
Use 4in x 4in posts for fences of 5ft and over and 3in x 3in posts for anything under 5ft.